Request a Call Back
This is a placeholder for the Yext Knolwedge Tags. This message will not appear on the live site, but only within the editor. The Yext Knowledge Tags are successfully installed and will be added to the website.
,
This is a placeholder for the Yext Knolwedge Tags. This message will not appear on the live site, but only within the editor. The Yext Knowledge Tags are successfully installed and will be added to the website.
Blog Layout

Purdy Products - Stera Sheen

The Team at Specialized Equipment, LLC • May 1, 2020
A message from Purdy Products

While Stera-Sheen Green Label was originally designed for clean in place equipment applications, it is an EPA registered Sanitizer approved to clean and sanitize surfaces, including food contact surfaces. Once properly mixed Stera-Sheen Green Label can be used to wipe down surfaces such as door knobs, counter tops, tables, etc. Many customers mix Stera-Sheen Green Label in a Quart spray bottle for an easier application on surfaces.
Below we have included directions for use with mixing ratios. As the pandemic has caused a shortage for cleaners and sanitizers; and with Stera-Sheen Green Label you get both for cleaning surfaces.
Spray Bottle Directions 
for Use
 
Recommended Mixing Ratio
1 Tablespoon Stera-Sheen Green Label per 1 quart of water
  •     Warm water is recommended
  •     Powder should be fully dissolved in water prior to use
Cleaning:
  1.     Remove any solids or debris from the surface.
  2.     Spray as necessary to completely coat the surface(s) with Stera-Sheen Green Label solution.
  3.     Brush clean and/or wipe with clean towel until visibly clean.
Sanitizing:
  1.     Remove any solids or debris from the surface.
  2.     Spray as necessary to completely coat the surface with Stera-Sheen Green Label solution.
  3.     Allow to soak for at least 60 seconds.
  4.     Use clean towel to remove excess solution or to dry.
Bucket Directions
 for Use
 
Recommended Mixing Ratio
1-2 ounces of Stera-Sheen Green Label with 1 gallon of water
  •     Warm water is recommended
  •     Powder should be fully dissolved in water prior to use
Cleaning:
  1.     Saturate a clean towel or dip a brush in Stera-Sheen Green Label solution.
  2.     Brush and/or wipe until surface is visibly clean.
Sanitizing:
  1.     Using a clean towel completely coat the surface with Stera-Sheen solution.
  2.     Allow to soak for at least 60 seconds.
  3.     Use clean towel to remove excess solution or to dry.
Please Note:

  •      Spray bottle should be indicated for use with Stera-Sheen Green Label Sanitizer & Cleaner solution only. Do not use or mix spray bottle with any other chemicals.
  •     After 4 hours, Stera-Sheen Green Label Sanitizer & Cleaner solution should be retested to indicate available chlorine per your local health department requirements, or the solution should be discarded. Mix new solution as needed following the correct dilution ratio.


**At the present time, no current product is EPA-registered as a virucide specific to the novel coronavirus, and Purdy Products makes no representation that control of COVID-19 is certified by US EPA. 

Make the most of the season by following these simple guidelines

By Hibu Websites • October 23, 2019
The new season is a great reason to make and keep resolutions. Whether it’s eating right or cleaning out the garage, here are some tips for making and keeping resolutions.

Keep in touch with site visitors and boost loyalty

By Hibu Websites • October 23, 2019
There are so many good reasons to communicate with site visitors. Tell them about sales and new products or update them with tips and information.

Tips for writing great posts that increase your site traffic

By Hibu Websites • October 23, 2019
Write about something you know. If you don’t know much about a specific topic that will interest your readers, invite an expert to write about it.
Share by: